Aluminum Sim Racing Cockpit Pro Silver | SIMGASM

The chassis that leaves nothing on the table

Every serious sim racing setup eventually arrives at the same question: is the cockpit keeping up with the hardware? A direct drive wheelbase producing 20 or more newton metres of torque, a set of load cell pedals demanding a rigid mounting surface, a motion platform requiring a frame that can transfer forces without absorbing them — these are not theoretical requirements. They are the daily reality of a high performance sim racing environment, and they demand a chassis that is genuinely engineered to meet them.

The SIMGASM Aluminum Sim Racing Cockpit Pro is that chassis. This is the flagship of the SIMGASM cockpit range, built without compromise for sim racers who want maximum rigidity, maximum adjustability, and a setup that grows with their ambitions rather than holding them back.

Zero flex by design

The structural foundation of the Pro is built from ultra strong aluminum profiles combined with heavy duty steel mounting components at the critical load bearing interfaces. This combination is deliberate. Aluminum profiles provide the lightweight rigidity that makes the overall chassis strong without unnecessary mass, while steel hardware at the connection points delivers the clamping force and dimensional stability that high torque wheelbases and demanding pedal sets require.

The result is a cockpit that does not flex. Not under full force feedback load, not under heavy brake pressure, not during aggressive heel and toe inputs. When the simulation sends a signal through your hardware, it arrives at your body intact — which is precisely the point of a purpose built sim racing chassis at this level.

Wheelbase compatibility without limits

The Pro supports bottom mount, front mount, and side mount wheelbase installation, covering the full range of mounting configurations used across the direct drive wheelbase market. Whether your wheelbase of choice mounts from below the plate, from a front facing profile, or from a side bracket configuration, the Pro accommodates it without requiring aftermarket adapters or structural modification.

This breadth of compatibility matters for a flagship cockpit. The hardware ecosystem in sim racing moves quickly, and a chassis that locks you into one mounting standard becomes a limitation the moment you decide to upgrade or change your wheelbase. The Pro removes that constraint entirely.

Pedal mounting built for real load cell performance

Load cell pedal sets — particularly brake pedals calibrated for high pressure inputs — place significant and repeated stress on the mounting surface beneath them. A pedal deck that flexes under heavy braking creates inconsistency in the pedal feel and, over time, works against the precision that load cell technology is designed to deliver.

The Pro provides a strong and stable mounting solution for even the most demanding pedal sets currently available. Adjustable pedal assembly height and angle give you the ability to dial in the exact pedal position and incline that your driving style and physical dimensions require, with enough range to accommodate drivers of different sizes across the full length of the chassis.

Cable management built into the frame

A high performance sim racing setup generates a significant amount of cabling. Wheelbase power and data cables, pedal USB connections, handbrake wiring, shifter leads, bass shaker runs — in a complex rig, cable chaos is a genuine problem that affects both the visual quality of the setup and the practical experience of using it daily.

The Pro addresses this at the chassis design stage rather than leaving it as an afterthought. Integrated cable passthrough points are built into the frame at the front, middle, rear, and near the wheel mount position, providing dedicated routing paths that keep cables contained, protected, and out of sight. The result is a setup that looks as considered as it performs.

Motion platform ready from the factory

The Pro is engineered to be motion platform ready as standard. For sim racers who are building toward a dynamic platform or who are already running one, the chassis provides the structural foundation needed to integrate without modification. This is a detail that separates a true flagship cockpit from a chassis that simply looks the part — genuine motion readiness requires structural decisions made at the design stage, not bolt on solutions added later.

Included as standard

The Pro is delivered with a heel rest plate, a shifter arm, and rubber feet included as standard. These are not accessories to purchase separately — they are part of a complete chassis package that is ready to build into a full sim racing setup from the moment it arrives.

Built for every driver, built for the long term

The adjustability built into the Pro spans a range broad enough to suit drivers of different heights, proportions, and driving preferences. Seating position, pedal placement, wheel height, and mounting configuration all adjust to match the driver rather than requiring the driver to adapt to the chassis.

The durable construction and premium material choices throughout mean the Pro is not a chassis you replace when your setup improves. It is the chassis your setup improves around.

• Flagship aluminum sim racing cockpit designed for zero flex performance
• Ultra strong aluminum profiles with heavy duty steel mounting components
• Compatible with bottom mount, front mount, and side mount wheelbase installation
• Strong and stable pedal mounting for demanding load cell pedal sets
• Adjustable pedal assembly height and angle
• Integrated cable passthrough points at the front, middle, rear, and wheel mount area
• Motion platform ready as standard
• Suitable for a wide range of driver sizes
• Includes heel rest plate, shifter arm, and rubber feet as standard
• Durable construction engineered for long term daily use
• Available in silver